RealRacingCraftsmen

RRC DRIVER + CAR SIDE BUNDLE — Motorsport Hydration Connector Bundle

€149,99 EUR

Sale Sold out

Taxes included.

Quantity

Both sides of the system, one package. The Driver Hydration Kit handles everything on the driver side. Connector housing, tubing, bite valve and velcro tube positioners. The Car Side Connector mounts permanently on your roll cage. Your driver snaps in when they get in, presses the button and it springs apart cleanly when they get out. Complete, ready to install, nothing else needed.

Standard configuration: Male CPC driver side, Female CPC car side, one way spring check valve included. Everything set up the right way from the start.

All RRC and SRC products use the same 4x7mm food-safe silicone tubing — everything in the system works with this tubing size.

Professional endurance racing connector technology at a fraction of the cost of traditional motorsport suppliers — without compromising on performance.

Key Features

Complete Driver and Car Side Setup

Male CPC Driver Hydration Kit — standard driver side configuration
Female CPC Car Side Connector — standard car side configuration
Press the button on the female fitting to disconnect — springs apart cleanly every time
Watertight on connect and disconnect — no drips even with a full line

Driver Hydration Kit

ASA construction — heat resistant, UV stable, impact resistant
Ridged grip on both halves for secure handling even with gloves
Two bolt-together halves wedge the CPC fitting and radio plug securely in place
Spacers included for most radio plug sizes — works with virtually any comms setup
1m food-safe silicone tubing (4x7mm)
Bite valve — bite to drink, release to seal, watertight when not in use, hand wash only
2x Velcro Tube Positioners with helmet sticky pads — velcro pre-applied, position anywhere along the tubing

Car Side Connector

ASA construction — heat resistant, UV stable, impact resistant
Two bolt-together halves wedge the 3/16" CPC fitting and radio plug securely in place
Spacers included for most radio plug sizes
Integrated hose clamp slits for secure roll cage or roll bar mounting
Hose clamps included
One way spring check valve included — no backflow, no drips when disconnected, keeps the system primed

Compatible Products

RRC DrinkBox — The heart of the system. Connect your Car Side Connector tubing straight to the DrinkBox outlet.

Race Bottle — 950ml insulated bottle. Both caps included with every RRC Race Bottle — CPC Quick-Connect for in-car use, Sipping Cap for paddock and travel.

Race Bottle Cap — CPC Quick-Connect Cap for in-car use, Sipping Cap for paddock and travel.

RRC Endurance Bottle Dock — Mounts your Race Bottle in the car. Integrated 3/16" CPC fitting connects directly to the DrinkBox inlet tubing.

SRC Bottle Mount — Simple upright bottle mount for your 4040 profile rig. For sim racing use at simracingcraftsmen.com

RRC Tubing — Same 4x7mm food-safe silicone with pre-installed insulation sleeves. Available in 2m or 4m.

Bite Valve — Replacement bite valves. Replace regularly for best hygiene.

Velcro Tube Positioner — Need extras? Available in 2 or 4 pack.

One Way Spring Check Valve — Replacement check valves for the Car Side Connector. Replace periodically for best performance.

CPC Coupling — 3/16" dry break coupling. Add snap points anywhere in your tubing run or panel mount anywhere in the car.

Care and Maintenance

Designed for low-maintenance, hassle-free use.

After every use: Flush the system with clean water for 20-30 seconds, then run briefly without liquid to clear excess moisture
After sugary drinks or isodrink: Always flush thoroughly with clean water immediately after use to prevent buildup
Regular cleaning: Fill your bottle with clean water and dissolve a cleaning tablet — run the full bottle through the system, then flush thoroughly with clean water and run dry
Deep clean (as needed): Use warm water with a bit of vinegar through the connector, then rinse thoroughly and run dry

Avoid alcohol-based cleaners — they may reduce the lifespan of the seals and fittings.