• close up of motorsport hydration bottle holder mounted on a race car roll cage.
  • A close-up shot of an SRC Drinkbox hydration canister mounted in a black holder inside a race car, with the brand logo and 'Hydrate Focus Perform' text clearly visible.
  • close up of side of racing hydration quick change bottle holder for endurance racing mounted on a roll cage
1 10

RealRacingCraftsmen

RRC ENDURANCE BOTTLE DOCK — QuickSnap Racecar Bottle Dock

RRC ENDURANCE BOTTLE DOCK — QuickSnap Racecar Bottle Dock

€149,99 EUR
€149,99 EUR
Sale Sold out
Taxes included.

Quick-release bottle systems are used in endurance racecars all over the world — from Le Mans to local club racing. The RRC Endurance Bottle Dock is the real thing. Slam your Race Bottle in, the integrated CPC fitting makes a watertight connection and the latch locks it in place. Swap it out in seconds with one hand. Built to handle the forces of real racing, tested in real racing environments.

How it works
Mount onto your roll cage or roll bar using the included hose clamps. Your Race Bottle with CPC cap slots in and docks directly into the integrated Dry Break fitting in the dock. The top latch locks the bottle securely, tested to handle the roughest conditions on track. Route your tubing from the dock straight to your DrinkBox. Everything fits together in one go. Optionally add the included tubing or use your existing DrinkBox tubing directly.

Key Features

Integrated 3/16" CPC Dry Break Fitting

  • CPC fitting built directly into the dock
  • Race Bottle with CPC cap docks straight in — instant watertight connection
  • Dry break disconnect — no drips even with a full bottle
  • Must be used with the Race Bottle CPC Quick-Connect Cap

QuickSnap Latch Mechanism

  • Top latch locks the bottle securely in place
  • Tested to handle the roughest conditions on track
  • One handed bottle swap, slam in, snap out in seconds
  • Built for pitstop bottle swaps and endurance driver changes

Roll Cage & Roll Bar Mounting

  • Integrated hose clamp slits for secure mounting onto roll cage or roll bar tubing
  • 2x hose clamps included
  • Mounts in any position to suit your car layout
  • 3M backed rubber included for extra rigidity on roll bar

Engineered Open Lattice Structure

  • 45 degree reinforced lattice design: strong, light and open
  • ASA construction: heat resistant, UV stable, impact resistant
  • Satin black finish

Compatible Products

RRC DrinkBox — The heart of the system. Connect the dock tubing straight to the DrinkBox inlet — same 4x7mm spec, all fits in one go.

Race Bottle — 950ml insulated bottle. Must be used with the CPC Quick-Connect Cap.

Race Bottle Cap — CPC Quick-Connect Cap required for use with the Endurance Bottle Dock.

RRC Tubing — Same 4x7mm food-safe silicone with pre-installed insulation sleeves. Available in 2m or 4m.

RRC Car Side Connector — Complete the system. Mounts on the roll cage, your driver plugs in their Driver Hydration Kit every time they get in.

CPC Coupling — 3/16" dry break coupling. Add snap points anywhere in your tubing run or panel mount anywhere in the car.

RRC Connector Offset Plate — Need to bring the Car Side Connector closer to the driver? The offset plate mounts to the roll cage and positions the connector exactly where you need it.

Care and Maintenance

  • After every use: Flush the tubing with clean water for 20-30 seconds, then run briefly without liquid to clear excess moisture
  • After sugary drinks or isodrink: Always flush thoroughly with clean water immediately after use to prevent buildup
  • Regular cleaning: Dissolve a cleaning tablet in a full bottle of water — run through the system, flush with clean water and run dry
  • Deep clean (as needed): Use warm water with a bit of vinegar, then rinse thoroughly and run dry
  • Bite valve: Hand wash only — replace regularly for best hygiene
  • Tubing: Replace periodically for best hygiene — see RRC Tubing

Avoid alcohol-based cleaners — they may reduce the lifespan of the tubing and seals.

Exploring Sim Racing?

The SRC Endurance Bottle Dock brings the same QuickSnap technology to your sim rig. 4040 profile mounting, same engineering, built for sim racing use. Find it at simracingcraftsmen.com

What's in the box?

  • 1x RRC Endurance Bottle Dock
  • 2x Hose clamps
  • (With tubing configurations) Insulated food-safe silicone tubing: same 4x7mm spec as the entire RRC and SRC system, with pre-installed insulation sleeves
  • (With bottle configuration) 1x Race Bottle with CPC Quick-Connect Cap
View full details